Results 1 to 10 of 10

Thread: Tapered fin JL cylinders needed

  1. #1

    Tapered fin JL cylinders needed

    I'm looking fo a good set of tapered fin, 61" JL cylinders for a bottom end that I have. Can pay $ or have LOTS of Harley JD parts to trade. How about a swap for a set of 29 only 74" cylinders?
    PM or email me.
    Thanks
    Mark Masa

  2. #2
    Join Date
    Nov 2008
    Location
    new britain pa
    Posts
    3,135

    Re: Tapered fin JL cylinders needed

    It would be easier to find Hilary's emails. I bought one and over paid for it. You'll find a pair of fh cylinders before you find jl/jh cylinders. If you can live with the internal differences. That's the way to go. Problem is the last set i saw for sale was $9,500.(jim d. in Buffalo) Maybe Stuart in oz will do a run

  3. #3

    Re: Tapered fin JL cylinders needed

    Rob
    They can't be that rare. I've had several sets go through my hand over the years but never planned on doing a JL so....
    Heindsight = 20/20
    Stuart from JD jugs does make tapered fin 61" Ricardo cylinders and that's an option too. Just trying to use OEM parts if possible.
    Mark

  4. Re: Tapered fin JL cylinders needed

    Hello Mark
    I might be able to help You. I got a set laying somewhere, think they are ricardo cylinders.
    I´ll find them and take some photos and mesurements.
    Regars
    Tom

  5. #5

    Re: Tapered fin JL cylinders needed

    Thanks Tom
    Do you have my email address?
    If not, you can find it in the contact section at http://www.linkcycles.com
    Mark

  6. Re: Tapered fin JL cylinders needed

    Hello Mark

    Have You got my mail??

    regards

    Tom

  7. #7

    Re: Tapered fin JL cylinders needed

    Email or a PM? No to both.
    Mark

  8. Re: Tapered fin JL cylinders needed

    I've send it again to mark-linkc.....

    Tom

  9. Re: Tapered fin JL cylinders needed

    well Mark

    I've send you a new mail with new photos and confirm, the messurement of the bores and that the bores are clean.

    I wonder why You dont get my mails.

    Regards

    Tom

  10. #10

    Re: Tapered fin JL cylinders needed

    I'll look in my junk mailbox. That's where it was last time.
    Thanks
    Mark

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Unknown Compensator Sprocket- tapered shaft
    By Bigincher in forum Engine, Transmission & Clutch
    Replies: 51
    Last Post: 12-01-2017, 08:58 PM
  2. Ricardo tapered fin racing cylinders
    By cylinders in forum Harley Pre 1936
    Replies: 9
    Last Post: 02-22-2017, 05:34 AM
  3. Tapered Cylinder Fins? - eBay JD
    By whp in forum Harley Pre 1936
    Replies: 10
    Last Post: 08-11-2016, 09:32 AM
  4. Replies: 14
    Last Post: 12-04-2015, 03:03 PM
  5. WTB: 18 or 19 tooth tapered motor sprocket
    By xsqzme in forum Motorcycles & Parts Wanted
    Replies: 0
    Last Post: 01-01-2010, 09:59 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •